What the error means
Microsoft's article on this code is short and direct: the issue is caused by a corrupted Outlook profile. When you try to send or receive, Outlook shows either "0x8004010F: Outlook data file cannot be accessed." or "0x8004010F: The operation failed. An object could not be found." In both cases the profile, the set of settings that tells Outlook which accounts you have and where their mail is stored, no longer points correctly at the default data file.
The data file itself is often fine. That is why Microsoft's fix is not to repair or replace your mail, but to note where the existing data file lives and build a fresh profile around it. Done in that order, the new profile picks up the same messages, folders and contacts.
Microsoft's article applies to Outlook 2010 and Outlook 2013, and its steps use the Mail item in Control Panel. If you run a newer version of classic Outlook and a label below does not match what you see, use Microsoft's "Create an Outlook profile" instructions for your version, which cover the same task.
Common causes
- A corrupted Outlook profile, which is the only cause Microsoft names for this code.
- The profile can no longer reach the default data file, which is what the first error message says.
- The article's steps are written for POP3 and IMAP accounts that keep mail in a local .pst data file, so that is where the error is documented.
How to fix it
1. Find the location of your default data file
Write this down before changing anything, because the new profile will reuse it.
- Select Start, then Control Panel, then Mail.
- In Mail Setup - Outlook, select Show Profiles.
- Select your current profile, then Properties.
- Select Data Files. On the Data Files tab, note the name and location of the default data file, which is the one with a check mark.
- Select Close.
2. Create a new profile with automatic account setup
- Back in Mail Setup - Outlook, select Show Profiles.
- On the General tab, select Add, type a name for the new profile and select OK.
- In Add Account, enter your email account information and select Next.
- When the account is configured, select Finish.
Microsoft notes that if your mail server supports both IMAP and POP3, automatic setup creates an IMAP account. If you want POP3 and your existing local mail, use the manual method in the next step instead.
3. Or create it manually and attach the existing data file
Use this to keep your existing POP3 mail in the same file.
- In the Mail dialog box, select Add, name the profile and select OK.
- Select Manually configure server settings or additional server types, then Next.
- Choose Internet E-mail, then Next, and type your account details. Select Test Account Settings to check them.
- Select Existing Outlook Data File, then Browse, and choose the file you noted in step 1. Select OK.
- Select Next, close the test dialog, then select Finish.
If you are unsure of the server details, Microsoft's advice is to ask your internet service provider.
4. Make the new profile the default
On the General tab of the Mail dialog box, select Always use this profile, pick the new profile from the list and select OK. Outlook now opens with the working profile.
5. Reopen any other .pst files
If you used more than one data file, start Outlook, select File, Open, then Open Outlook Data File. Browse to each additional .pst file and select OK. It appears in the Navigation pane.
If nothing works
If the new profile shows the same error, the data file itself may be damaged. Microsoft's general send and receive guidance includes running the Inbox Repair Tool on the .pst file, which takes around fifteen minutes. Repairing the Outlook program is the next step on that same Microsoft page. As a general precaution, keep the old profile until the new one has worked for a few days, so you can switch back if needed.
What we checked
On 2026-11-19 we read Microsoft's Learn article "Error 0x8004010F when sending or receiving email" (original KB 2659085). It names a corrupted Outlook profile as the cause, quotes both error messages, and documents finding the default data file, creating a new profile automatically or manually with the existing data file, setting it as default and reopening other .pst files. The article is written for Outlook 2010 and 2013. We did not reproduce the error.
Last checked: 2026-11-19.