# UPS Sizing for Office Network Gear: Calculate VA, Runtime and Replacement

> Size a UPS for a router, switch, access points and NAS: add up watts, allow headroom, check the VA rating, read the runtime chart and plan battery replacement.

Source: https://www.epifive.com/blog/ups-sizing-office-network-gear · Published 2026-10-25 · EpiFive

## Key takeaways

- Size a UPS by adding up the watts of every connected device, then choosing a model with a watt rating 20 to 25 percent above that load.
- Watts are the key rating, and VA divided into watts gives the power factor, so compare watt ratings between models rather than VA alone.
- Runtime depends on the actual load, so read the manufacturer's runtime chart and keep only essential devices on battery.
- Most UPS batteries last three to five years under normal conditions, so record the install date and plan the replacement.
- For network gear, the target is usually minutes to ride out dips and shut down cleanly, not hours.

To size a UPS for office network gear, add up the watts that the router, switch, access points, modem and NAS draw, add 20 to 25 percent headroom, and choose a unit whose watt rating covers that figure and whose VA rating is higher than the watt load. Then confirm the runtime from the manufacturer's runtime chart at your actual load. The battery will need replacing, typically after three to five years.

This guide is for small office owners and part-time administrators who have a rack or shelf of network equipment with no battery protection. By the end you will have a load total, a minimum UPS rating, a runtime check, and a replacement calendar.

## VA, watts and power factor

UPS units are rated in volt-amperes (VA) and in watts. The two differ because of power factor, which is the ratio of watts to VA. Schneider Electric's buying guide gives an example power factor of 0.8 (80 percent) and notes that VA is usually higher than watts.

Eaton's UPS handbook says watts measure real power and are the key rating, so a 1000 VA / 900 W UPS has more usable capacity than a 1000 VA / 600 W unit. For converting equipment wattage to VA, it divides by the power factor, and says that newer IT equipment such as computer servers typically has a power factor of 0.9 or greater, while legacy PCs can be 0.60 to 0.75.

The practical rule is to compare both ratings and check the watt figure first.

| Term | Meaning | Where it appears |
| --- | --- | --- |
| Watts (W) | Real power the load consumes and the UPS can supply | UPS spec sheet, device label |
| Volt-amperes (VA) | Apparent power | UPS name and spec sheet |
| Power factor | Watts divided by VA | Spec sheet, or implied by the two ratings |
| Runtime | Minutes the battery can supply a given load | Manufacturer runtime chart |

## Step 1: List the devices and measure the load

Decide what must stay up. For a typical small office, essential items are:

- Internet modem or ONT.
- Router or firewall.
- Core switch (and the PoE load it supplies).
- Wireless access points, if powered by the switch the draw is part of the switch's draw.
- NAS or small server.

Leave printers, monitors and desktop PCs off the UPS unless you have a reason. Schneider's guide notes that more connected equipment reduces runtime and suggests reserving backup power for the most essential devices. Laser printers in particular draw a lot of power when they warm up.

Find each device's wattage from the label on the device or its power adapter. Labels show the maximum, which is usually higher than typical use. A power meter plugged in between the device and the wall shows what it actually draws; use the highest value you see under load. If a device lists only volts and amps, multiply them to get VA, which overstates watts.

Example only, with illustrative figures that you must replace with your own:

| Device | Watts (from label or meter) |
| --- | --- |
| Fibre modem | 10 |
| Router or firewall | 25 |
| 24-port PoE switch including two access points | 90 |
| NAS with four drives | 60 |
| **Total** | **185** |

## Step 2: Add headroom

Schneider's guide says to ensure the output watt capacity is 20 to 25 percent above the load. Using the upper end of that range:

```text
185 W x 1.25 = 231 W minimum watt rating
```

So the example needs a UPS rated for at least about 231 W. Network gear grows: another access point, a second NAS, a PoE camera. Headroom makes room for that.

## Step 3: Check the VA rating against the watt load

Schneider says a UPS should have a VA rating higher than your total device watt load. Check both:

- The UPS watt rating is at least your load times 1.25.
- The UPS VA rating is above your watt load.

A model rated at, say, 600 VA / 330 W would meet both for the example. Do not choose on VA alone: two models with the same VA can have different watt ratings, and the watt rating is the one that limits you.

## Step 4: Check runtime at your load

Runtime depends on the actual load, not the nameplate. Manufacturers publish runtime charts per model. Find your total (in watts) on the chart for the exact model and read the minutes.

Eaton's rule of thumb is that halving the load triples the runtime, which is why a lightly loaded UPS gives surprisingly long runtimes and a fully loaded one gives very short ones. Eaton also notes that adding more batteries does not increase the power rating of the UPS.

Decide the goal first:

| Goal | Typical approach |
| --- | --- |
| Ride out short dips and flickers | A few minutes of runtime is enough |
| Shut down the NAS cleanly | Enough minutes for the NAS to finish its shutdown, plus margin |
| Keep the internet up through an outage | Much larger battery capacity; check the runtime chart |

For most small offices the aim is the first two. Keeping an office online for hours needs a much larger system than a small line-interactive unit, or an alternative like a generator, and is a different project.

## Step 5: Shut down gracefully

A UPS that only buys minutes needs to tell the NAS to shut down. Many UPS models offer a USB data connection or an optional network management card, and many NAS systems can be configured to watch a UPS. The details depend on your NAS and UPS models, so check both vendors' documentation, and test by pulling the UPS plug from the wall during a quiet period and confirming the NAS shuts down cleanly.

## Step 6: Plan battery replacement

Eaton's Tripp Lite buying guide says most UPS batteries last three to five years under normal conditions, and that many units allow replacing the internal battery rather than the entire UPS. Eaton's handbook advises noting the battery expiration date so a replacement plan is in place.

Make a small record for each unit:

```text
UPS model:          ___________
Location:           ___________
Install date:       ___________
Battery install:    ___________
Replace by:         install date + 3 years (review at 3, replace by 5)
Last runtime test:  ___________
Protected devices:  ___________
```

Test the runtime every six months or so by removing mains power briefly when it is safe, and replace the battery early if the runtime has dropped noticeably or the unit reports a battery warning. Heat shortens battery life, so keep the UPS out of a hot cupboard with no airflow. That is general practice rather than a figure from the sources above.

## Troubleshooting

| Symptom | Likely cause | What to do |
| --- | --- | --- |
| UPS overload alarm at start-up | Load exceeds the watt rating, often a laser printer or a PoE switch with many devices | Remove non-essential devices or choose a higher-rated UPS |
| Runtime much shorter than the chart | Ageing battery, or the load is higher than estimated | Measure the load with a power meter; replace the battery if it is past three to five years |
| NAS does not shut down cleanly | UPS data connection or NAS UPS setting missing | Connect the data cable or network card and configure the NAS to monitor the UPS |
| UPS beeps and switches to battery frequently | Poor mains supply, or the voltage thresholds are too tight | Check the UPS settings in its manual and the mains condition |
| New access point causes an overload | The headroom was used up | Re-do the load total and size up at the next replacement |

## Closing checklist

- List essential devices only and measure or read their watts.
- Add 20 to 25 percent headroom to the total.
- Choose a model whose watt rating covers the figure and whose VA is above the watt load.
- Read the runtime chart for your load and confirm it meets your goal.
- Connect a data or network link so the NAS shuts down cleanly.
- Record the battery date and set a replacement reminder at three years.

If the network has a guest VLAN and managed switch, read [VLAN setup for a small office](https://www.epifive.com/blog/vlan-setup-small-office-guest-wifi); for the storage on the UPS, see [NAS vs cloud storage for a small business](https://www.epifive.com/blog/nas-vs-cloud-storage-small-business).

## References

- Schneider Electric (APC), UPS buying guide: https://www.se.com/us/en/work/support/product-support/ups-buying-guide-for-selecting-a-battery-backup-system/
- Eaton UPS and power management fundamentals handbook: https://www.eaton.com/content/dam/eaton/products/backup-power-ups-surge-it-power-distribution/backup-power-ups/eaton-ups-fundamentals-handbook-en-us-2025.pdf
- Tripp Lite by Eaton, UPS battery backup buying guide: https://tripplite.eaton.com/products/ups-buying-guide

## Frequently asked questions

### How do I know what size UPS I need for a router and switch?

Add up the wattage of every device you will plug into the UPS, then pick a model whose watt rating is 20 to 25 percent above that total and whose VA rating is higher than the watt load. Use the manufacturer's runtime chart for your load to confirm it gives the minutes you need.

### What is the difference between VA and watts on a UPS?

Watts measure real power and are the key rating for what a UPS can supply. VA is apparent power, and a UPS is usually rated in both. Power factor is the ratio of watts to VA, so a 1000 VA UPS rated at 600 W has less usable capacity than a 1000 VA UPS rated at 900 W.

### How long does a UPS battery last?

Eaton's Tripp Lite buying guide says most UPS batteries last three to five years under normal conditions, and that you can replace the internal battery instead of the whole unit. Heat and heavy load shorten that, so check the battery expiry date and test the unit regularly.

### Does a bigger UPS give me longer runtime?

Only because a larger unit usually has bigger batteries and runs at a smaller share of its capacity. Eaton notes that cutting the connected load in half roughly triples runtime as a rule of thumb, and that adding batteries does not raise the power rating of the UPS.